How to Clean and Straighten AC Condenser Coils

The condenser coils are a vital part of your air conditioner unit. Without it, your aeration and cooling system won’t work appropriately. It is therefore vital to keep it in working condition.


The AC condenser coils need regular maintenance and cleaning along with the indoor AC evaporator coils because the condenser unit is other half a split central air conditioner system. The purpose of the condenser coil is to release the heat absorbed by the refrigerant at the evaporator coils inside the home so it’s ready for the next cooling cycle. If the condenser coils are clogged with dirt or the fins are bent it will block air flow through the coils and interfere with the heat exchange. This causes the system to work harder and drives up your electric bill.


Bent AC Condenser Coil Fins

The air conditioner system was installed by the home builder and are now about 12 years old. The Heil “entry model” or economy condenser units have coils that are protected by a wire grille which in reality isn’t much protection. I noticed the condenser coil fins had become bent and damaged sometime in the past 2 years. Were the fins bent by the hail storm or more likely by the pressure washer guy?

The bent condenser coil fins are very noticeable in the 2012 photo. The damaged fins are straightened by fin combing in the 2014 image:

Outdoor AC Condenser Units Before and After Fin Straightening

How to Clean and Straighten AC Condenser Coils

I called my HVAC service company for the twice a year seasonal maintenance and asked for condenser coil cleaning and fin combing to straighten the bent fins which cost an extra $125 per unit.

These are 3 ton (or 36,000 BTU/hr) condenser units. The coils are painted black by the factory which has mostly worn off. The coils show numerous silver looking areas with bent fins or impact damage. The individual strikes could be something thrown by the lawn mower or a hail strike. That bent fins near ground level are probably from careless use of the weedeater. I believe the pressure washer guy caused the large area of bent fins at the left corner when he cleaned the house (BTW – never pressure wash AC coils!):

Outdoor AC Condenser Bent Fins

The condenser unit wire grille must be removed to comb and straighten the fins. The AC service tech shutoff the electricity at the outdoor service disconnect before starting work, then removed …


Read more: https://www.handymanhowto.com/clean-straighten-ac-condenser-coils/



There are many different ways to keep your home comfortable. A ductless cooling and heating system provides efficiency and energy savings ideal for each and every home.


Modern living room with wall-mounted ductless unit

Most people have heard of ductless cooling and heating systems, and they have probably seen the small, indoor devices installed high on walls in homes, restaurants or office buildings. But what do you really know about these systems?

1. They Offer Highly Flexible Solutions

Whereas traditional heat pumps and central air conditioning systems force cooled and heated air through ducts, ductless systems deliver air directly into different zones. They are comprised of a small outdoor unit and one or more indoor units that require nothing more than mounting capabilities and access to electricity.

Sometimes referred to as split systems, multi-split systems, or split-ductless systems, ductless cooling and heating offers home and business owners a cost-effective way to replace inefficient window units, space heaters and electric baseboard heaters. They can be installed in home additions, new construction, condominiums and apartments, or to improve temperature control in specific rooms. Ductless systems can even be fit for buildings that currently use ducted forced-air systems.

2. They Save You Money

One of the biggest reasons why homeowners switch to ductless cooling and heating is overall cost savings. In recent years, utility costs across the country have skyrocketed. When a home’s temperature depends upon an inefficient system, monthly bills can quickly climb out of control. Ductless systems operate on less power – they are smaller than traditional forced-air systems, and because the temperature-controlled air is delivered directly into a room, there is no loss in efficiency. Multi-split systems also allow homeowners to …


Read more: http://www.mitsubishicomfort.com/articles/ductless/5-advantages-of-ductless-cooling-and-heating-systems



Biomass has been around for the last 10 years, but only now is it becoming popular. What is it so? What did people discovered that gained their interest in such?


Wood burning stove image

Wood-fuelled heating systems, also called biomass systems, burn wood pellets, chips or logs to provide warmth in a single room or to power central heating and hot water boilers.

A stove burns logs or pellets to heat a single room – and may be fitted with a back boiler to provide water heating as well. A boiler burns logs, pellets or chips, and is connected to a central heating and hot water system. A wood-fuelled biomass boiler could save you up to £990 a year compared to electric heating.

The benefits of biomass heating

  1. Affordable heating fuel
    Although the price of wood fuel varies considerably, it is often cheaper than other heating options.
  2. Financial support
    Wood fuel boiler systems could benefit from the Renewable Heat Incentive.
  3. A low-carbon option
    The carbon dioxide emitted when wood is burned is the same amount that was absorbed over the months and years that the plant was growing. The process is sustainable as long as new plants continue to grow in place of those used for fuel. There are some carbon emissions caused by the cultivation, manufacture and transportation of the fuel, but as long as the fuel is sourced locally, these are much lower than the emissions from fossil fuels.

If you live in Scotland, view case studies and examples where homeowners have installed a wood-fuelled heating system.

Costs, savings and financial support


For boilers, an automatically fed pellet boiler for an average home costs between £9,000 and £21,000, including installation, flue, fuel store and VAT at 5 per cent. Manually fed log boiler systems can be slightly cheaper.

Pellet costs depend mainly on the size and method of delivery. If you have room for a large fuel store that will accept several tonnes of pellets at a time, delivered in bulk by tanker, you can keep the cost down to around £220 per tonne in most parts of the UK.

Logs can be cheaper than pellets, but costs depend on the wood suppliers in your local area, as they cost a lot to transport.If you have room to store more than a year’s worth of logs you can save money by buying unseasoned logs and letting them season for a year. Search for wood fuel suppliers in your area on the Biomass Suppliers List.


Savings in carbon dioxide emissions are very significant – up to 15.7 tonnes a year – when a wood-fuelled boiler replaces a solid (coal) fired system. Financial savings are more variable – if you replace an ….


Read more: https://www.renewableenergyhub.co.uk/benefits-of-biomass.html


Stay Warm and Safe with a Space Heater this Season

Heaters are very popular and you probably have one in your home to provide your household the warmth during months that are chilly. However, these are units that come with risks and you should be attentive to everything around your heater so that you are able to enjoy their convenience safely.


Space heaters are an effective way to stay warm. They’re incredibly energy efficient. They distribute heat evenly and operate quietly. A space heating system can effectively warm an area at a rapid rate, providing enough heat to keep you and your family comfortable.


On average these heaters warm spaces as large as 300 sq. ft. They spread warmth around the room and keep you feeling exceptionally comfortable. Using a space heating unit is a great way to reduce winter chill.

They offer a variety of amenities like: heat settings, temperature adjustments, multiple fan speeds, easy to use controls, and a remote control that make them an ideal winter option.

There are a variety of reasons to consider a space heater as a source of warmth this winter.

It can make up for inconsistent heat – as is often the case in apartment living – eliminate the need for central heating, keep a dorm room warm for the college student, or provide extra warmth when built-in versions aren’t enough.

Ideally, it’s a superior winter companion; however, there are safety facts you must remember. If used improperly, they can be dangerous. So if you plan on using one to keep warm this season, bear in mind a few essential safety tips to keep you and others safe this winter.

Avoiding Accidents

space-heater-safetyElectric heating sytems are a terrific way to stay warm, but it should be used with caution. First, consider the type of heater you plan to use. There are many varieties to choose from.
Because they are …These options contain a heating element that warms spaces at a rapid rate. Your unit might contain a hot coil, oil, bulb, or fan. This heating element gets hot so where you set up your space heater is important. Keep yours in a clear, accessible space, away from combustibles.


Read more: http://www.air-n-water.com/space-heater-safety.htm


Swamp Coolers or Evaporative Aircoolers for Home Use

Photo from findanoutlet.wordpress.com

One of the most affordable strategies to cool your living or working space is with evaporative coolers. Evaporative coolers, generally known as Swamp coolers are helpful machines for people who want to cool their houses. These coolers are among the safest, most effective and environment-friendly cooling systems available in the market. It is mechanics and concept is simple and it could efficiently cool and area without consuming lots of resources and energy. This is the perfect cooling system for everybody who is working with a tight budget.

Evaporative air coolers are recommended over air conditioners given that they use up less energy. When using evaporative coolers you’ll be able to lessen your energy consumption by more than 33 percent. Nevertheless, you to run these coolers you might need lots of water. Also, homeowners can pick to use the smaller evaporative coolers which are easy to install than the larger units which need ductwork in the home to spread the air.

An evaporative air cooler works on the principle of an endothermic reaction. An endothermic reaction is a procedure that absorbs energy in the form of heat. The evaporative air cooler passes air via a wet media. As the air goes through the water in the wick evaporates and the reaction brings about heat up to be absorbed.

There are several of evaporative designs that individuals can purchase. You have to evaluate your need such as space, cooling capacity to ensure you won’t have to spend much on a very expensive type. When choosing a swamp cooler, you should note the unit’s air moving capacity, as well as set up and maintenance prerequisites. Some swamp coolers may require more work than portable air conditioners for instance replenishing the water supply, draining the unit, and cleaning the cooling pads. Nevertheless, evaporative coolers are produced using a simplistic design, hence they have very minimal servicing need.

Prior to when you install an evaporative cooler, ensure that you look at the building codes of your area. After you’ve examined the codes, you must determine the location and mark the opening. You should then construct a platform of iron or wood and attach the platform to the opening. When fixing the platform, don’t forget to don’t cut any structural framework. The dimensions of the opening and the structure will depend on the instructions that come with the machine. If you’re not skilled with it, you may seek professional help to prevent damage and further accidents

There are plenty of sites that provide information on evaporative coolers. You could conduct your own little research to find out more about evaporative coolers.


Five Types of Heating Systems and Their Uses

When it is hot outdoors we would like to feel cool; and whenever it’s cold we want to be warm. Eventually even the best maintained system will break down and need to be replaced. It’s very easy to replace your heating and air system with the same type that you have but is it the best type for your residence or business. If you’re in the market to either purchase a brand new heating system or are attempting to replace a broken system, you should become knowledgeable about all the kinds of heating options that are available to you. As always, being aware of what is out there can have a big impact on your decision. Here are just some few heating systems that you might want to take into account at home.”

Photo by 5starphc.com

If renovating a house or place of business, you need to design the room in a fashion that boosts efficiency while lessening expenditure. This practical goal ought to explain to all decision-making during the renovation process. You should contemplate, of course, the utilities that run in a given space daily.

Heating and air systems are costly therefore you need to choose the right system to make your home or business comfy. By being aware of what type works best for your home or business will get you on track to make your house or business a comfy place. Here are a few of the more popular heating systems options you could have at home.

1. Forced Air System

A forced-air heating system does exactly what its name suggests: a furnace heats air by using up a number of fuels; then, fans or blowers force the heated air through the property. The heated air extends to each room of a house by using a ducting system, which is a network of pipes that leads to separate room openings. But, one disadvantage of forced-air furnaces is that they can waste fuel, which is a problem for both financial and environmental reasons.

2. Radiant Heating System

This type of system can take numerous forms, including a pot-bellied stove or in-floor tubing. The heat is directly moved to the cool surface, heating it up. It’s just like the forced air system for the reason that it may run on many different fuel types including gas, oil, propane, or electricity. Although it does a great job heating and creates an incredibly comfortable environment, this heating option can be costly to install and can take a while to heat up your home.

3. Hydronics

It is a similar idea to the radiant heating system. The difference is, the hot water from the boiler runs into baseboard units mounted on the wall. This system runs quietly, and the temperature may be controlled with accuracy and very quickly. However, the baseboard units should not be obstructed by furniture, so this is not the best option for each and every space.

4. Steam Radiating Heating System

Often called a cast iron upright radiator, this method isn’t very commonly used today. Generally, water is run through the unit and heated by a pilot, that turns the water to steam. The steam heats the iron, dispersing warmth throughout the room. The steam condenses back into the water and it is drained through more pipes. This is a very efficient, quick system, and incredibly comfy. However, it could be an ugly unit, and it limits furniture placement.

5. Geothermal System

Modern developments in technology have caused the geothermal heater. Very costly to set up, but efficient over time, many claim them to be quite cost efficient. Geothermal heaters use the energy from the earth and can be implemented for both heating and air conditioning.


Benefits of Water Heater

Water heater is an appliance that will last for a long period. That’s the reason why we actually don’t put much focus on it. In case the water heater fails or does not work any more, then it’s the perfect time to buy a another one. But first you have to know things that you should put into consideration before buying the replacement unitThese pointers are simply to give you the fundamental knowledge on water heater types and features. Yet, if you happen to still end up baffled and unsure on some decisions, it’s best that you simply contact a plumbing company to guide you every step of the way. Through them, you can make sure that the project will be done correctly.”

Photo by www.bellowsservice.com

Water heater replacement is an activity that is carried out rarely. Often it would take 5-10 years before you could find defects in it. If you’re having issues such as the hot water doesn’t last that much or the water have some odd smell and taste, then most likely it is indeed time to look for a replacement. Here are points that you must put into consideration before selecting one.

What type of power?

When you purchase a water heater, you may always wish to have an effective and cost-effective one. Water heater makes use of different types of energy such as solar, atmospheric gas, electric and more. If you want of saving fuel cost, choose solar water heater. And if you intend to be more eco-friendly, choose a natural gas heater. Additionally when you compare the operating costs of electric and gas water heater, the latter is more cost effective.

What size do you need?

To decide on the right water heater for your residence, you need to think about the size of your household as well as other things that add up to your Peak Demand Output Requirement. It is to make sure you aren’t squandering energy in water heating. A small (50- to 60-gallon) storage tank is normally sufficient for one to three people. A medium (80-gallon) storage tank is helpful for three to four people. A large tank is suitable for 4 to 6 persons. If you are not pretty sure in this decision, you could seek the guidance of a plumber to give you the best choice for your family needs.

Where will it be installed?

It’s a typical situation that replacement water heaters are placed on the same location of the previous one. Having said that, you should determine the height and width to be sure sufficient space exists for installation since there can be changes on the size or capacity of your water heater. For example, if your hot water use heightens and you must upgrade to a bigger tank size, it could be necessary to run plumbing to a different area so the new, larger unit will fit. What ever it can be, it is still advisable to let a professional plumber decide on the right spot.

Do you want a tank or tankless model?

Traditional storage water heaters utilize a tank to heat up the water within it. It is actually preferred by some since the tank water heater are less expensive in comparison with tankless. Tankless units heat water are now on demand and are more cost-effective. However, volume is fewer and a single tankless unit is normally suited to serve no more than two hot water demand points at a time. It’s an energy-efficient option, though has a high initial cost at sometimes two or three times the price of a traditional water heater.

Water heater replacement shouldn’t be accomplished for those that are not really knowledgable about it. It takes a skill and knowledge to accomplish such job. And so whenever you’re unsure on your selections, you must seek out professional help. A plumber is the best individual that will help you with this and they can guarantee that everything will be setup appropriately.


Tips On How To Prevent Sewer Backup From Taking Place

With regards to homeownership and dealing with problems, there are few things a lot more disheartening and frustrating than to learn that there’s a trouble with the septic system. With that being said, this doesn’t have guarantee that sewer backup is unavoidable. Actually, by taking steps to minimize the hazards, you could potentially lessen the chances of the need to call the plumber because of a sewer problem.”

Photo by vibrantneo.org

A sewer back up isn’t just horrible to look at, but it additionally poses great danger to the surroundings and your property. The cool thing is you can avoid the backup from happening. To avoid it from occurring you need to do the following:

Large Items

A few lifestyle tips may also help in the prevention of sewer issues. The very first is to be smart about what you happen to be putting down your drains. Tend not to flush or drain items like diapers, grease, or paper products as these only give rise to obstruction issues. Be sure to keep in mind the area of your sewer lines whenever planting new trees or putting in any landscaping. Plant roots are a typical issue of pipe breaks that could be easily prevented by considering installations and plantings thoroughly.

Cooking Oil

Another thing to remember is to be cautious what items are heading down the garbage disposal. Never pour grease, oils and fatty substances down the sink since it could harden and start collecting debris, which can cause a huge clog in your pipes and further on down to the connection to the main sewer line.

Shrubs and Trees

This really is something which can be difficult to handle, since roots seem to have a mind of their own. They could actually grow into the pipes, which can cause holes in them and then create blockages. Additionally, it can let the sewage to go into the ground. They even can crush the pipes in some instances. Even when you don’t have trees on your lawn, neighboring tree roots could actually creep beneath the ground and damage the pipes. The best way to avoid having to make such a costly repair is to work with a drain cleaning company to service your sewer system.

Backup Device

There are a number of sewer backflow devices that you can put in in the home’s sewer system in order to keep the sewage from backing up into your house when the main sewer blockage happens. You must set up the device in a way it goes on the residential sewer line that connects with your area’s district sewer line. For great outcomes you should make certain that system is put in by a professional.

Other Preventive Measures

There are many ways in which you can prevent sewer backup from occurring. One way is placing wooden or rubber plugs on your drains prior to a heavy rainstorm. Should you not wish to go on putting in the plugs before every heavy rains, it’s a wise decision that you set up permanent plugs. Again, you ought to make certain that plugs are installed by a professional.


Importance Of Furnace Maintenance

Maybe you are getting a brand new furnace or have one that was included with your house when you bought it, you have to carry out routine maintenance in order to make sure that your furnace operates at its best performance, and it’ll last a good long time. If you’re getting a brand new one it’s going to be easy to find out what routine maintenance is advisable for the brand you got. In case you have an old one you can probably go online and look up the brand, then search for the model number. You may have to make a call to figure out precisely what maintenance is recommended.”

Photo by www.absoluteair.com

Even if you might not be an expert heating repairman, you are still a property owner and learning how to maintain your heating system could save you money. Getting regular furnace maintenance assures house owners that their heating system with be without problems during the cold winter months. Regular maintenance keeps furnaces from burning an excessive amount of fuel, and makes sure that carbon monoxide does not leak in to the home. Scour the web for information on brand names and model numbers that you currently have. If you can’t get the information you are looking for or have some doubts about the credibility of the information you explored on, call the maker to ask about the required furnace maintenance.

Should your furnace is an older model and it was included with the house when you purchased it you should have a good furnace man go to your property and service it as soon as possible. When he is finished with servicing the furnace just ask him what he recommends as a routine maintenance plan. Have him give you a list of things you can do as the homeowner and what will need a service call to deal with.

It is extremely clear to see that you’re going to use your furnace more in the the fall and winter months. Early in the year and summer you either put your furnace on only its pilot light, or you will turn it completely off, then relight it come autumn. Knowing this is the normal routine you can do any servicing or maintenance during the months that you do not need it for heat. If it’s a very old furnace and you want to attempt to overhaul it entirely, then the time for that would be when spring is full set in and you won’t need the furnace for months.

You most likely don’t wish to try to overhaul your furnace all on your own, if you aren’t an experienced furnace professional. Even if you wish to be directly involved with the over haul you will have to contact a company to make arrangements to possess one of their pro’s come over and be the main worker while allowing you to be a very involved assistant. By doing this you won’t damage your furnace by accident. The pro will be right there to stop that. He’s going to also be able to notice in case there are any parts which are so worn that they have to be replaced. If the parts shall no longer be available he may be able to tell you where one can have the part made for you to install.


5 Ways Of Thawing Frozen Pipes in Winter

Every time any pipe in your plumbing system freezes, it really is put at risk for exploding. Which means it’ll freeze then break open. The water inside expands when frozen, putting pressure on the pipe. As water freezes, it expands slightly, and this also can cause your pipes to burst. It fuses with air and gas inside, triggering further enlargement and ultimately the pipe won’t be able to withstand the pressure and cracks open.”

Photo by nationalsafety.wordpress.com

In lots of parts of the country, temperatures might dip under freezing for many hours at a time. Frozen pipes call for fast attention from the successful, licensed plumbing company. Plumbing emergencies can be quite expensive for business and homeowners, especially during the winter. Normally, you will not even be aware that the pipe has broken. You’ll find out, however, when you see the damage it caused.

Getting this matter resolved by a professional plumber is always suggested, yet, if you’d like some pointers to thaw your frozen water pipes on the run, read the points given below.

1. Be sure that your pipe hasn’t cracked as a result of freezing. Freezing of water results in its expansion which actually causes cracks in the pipe. If your pipe has broken, it’s always best to have it replaced/repaired from a plumber company. Usually, pipes that exist these days never crack but merely get blocked.

2. Knowing that the pipe does not have any crack or crevice, turn-off the water running in the pipe. While those living in old houses might need to shut their main water supply, in newly built houses, people can simply isolate the frozen pipe from the remaining water system with a shut-off valve.

3. If you notice that the slow drip has ceased, you may need to increase the flow slightly. Do not forget that the faucets needs to be allowed to drip provided that temperatures are below the freezing mark. Additionally, consider allowing all faucets to drip like the showerheads and bathtub faucets.

4. To thaw the core of the pipe, the majority of plumber companies advise to wrap a towel round the pipe and pour hot water. This will give warmth to the pipe and melt the hard chunks of ice. One can also work with a handheld dryer to blow warm air to the section of the pipe that’s frozen so as to thaw it.

5. There are more other methods to thaw a pipe. A space heater placed close to a pipe can also be very efficient. Should the frozen pipe is beneath a sink close to an outer wall of your dwelling, for instance, open the cabinet doors and put the heater near to the cabinet. A space heater can be utilized along with other techniques and can keep the worker warm during the procedure. Heat lamps also work well. When employing a heat lamp, make sure to keep it a foot away from the pipe being thawed out. Don’t place it on a wet area, and be sure that water does not flow on the appliance.

Professional plumbers also assert the importance of using electric pipe heating tapes to thaw frozen water pipes. People also tend to use plumbing torches for this purpose, but in case of ABS and PVC pipes, they hardly work. If nothing proves to be useful, contact for frozen pipe repair from a leading plumber company.